Standard Shipping to
DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor
DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor

DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor

$18.19

Dispatch: Ship within 1-3 days
Shipping: US $3 to via Standard Shipping
Estimated Delivery: 8 - 22 business days
SKU: 1311440 Category:
Added to wishlistRemoved from wishlist 0

Buy DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor cheapest price

Specification:
 
Operating voltage: DC 12V-36V
Operating Current: <=15A
Driver Power: <=500W
Speed Voltage: 0.1V-5V
Operating Temperature: -40~85°C
Humidity: 90%RH
Stall protection: Yes
Enable Control: Yes
Over-current protection: Yes
Steering control: Yes
Speed control signal: Yes
Size: 63 x 42 x 17mm (L x W x H); Probe size 3mm, length: fixing hole center distance 57mm; width: fixed hole center distance 36.5mm
 
Power terminal Out:
 
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
 
Set for the control side:
 
GND: control terminal ground
VR: the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF: reversing control(connected to 5V or ground can charge the motor rotation direction)
M: tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL: enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V: 5V control terminal
 
HALL for the hall terminals:
 
5V: Hall power positive
Ha: Hall signal
Hb: Hall signal
Hc: Hall Signal
GND: Hall negative
 
Wiring:
 
Control terminal for SET:
 
1. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods: you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal: high and low output . IC can not understand the information with the customer request.
 
Hall signal inputs for hall:
 
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor hal signals positive, GND power supply negative signal to the motor hall.
 
Note: 
 
Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the seque, need to be adjusted, please parents who pay attention! If the line seque wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!!!
Motor driver board 12-36V DC power input, VCC positive power supply,GND power supply is negative.
Electrical wiring methods: Brushless DC motor for the three lines, corresponding MA/U, MB/V, MC/W
 
Tips:
 
If you use less than 60W, without additional heat sink , be sure to add more than 60W 
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
 
Package Includes:
 
1 x 12-36V 500W Brushless Motor Controler


Best DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor wholesale price

Specification: DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor

Weight 0.027 kg

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

RECENT PRODUCT REVIEWS
  1. Its very good item for me, usually I am using this for charging my power bank (10000mah). Very good.

  2. Excellent android box

    I bought one for us. And to be honest I was VERY SCEPTICAL. But once installed the sky is the limit on what you can do. Our kids are grown with their own children and even the grandchildren know how to operate it and love the video options. So we decided to get them their own and not to brag but mom and dads gift were the bomb. Even the grandchildren were excited 

  3. A+ If you use the right cup!

    After having it for a few days I love it! I tried it with different cups and mugs and you’ll want to use the a mug with a flat base to really spread the heat. I pre heat my mug while my coffee brews and it will stay hot as long as you’d like. I found the default high heat setting worked best for me. It’s not to expensive and makes a great gift. I got mine in black and it looks great on my desk at work.

  4. Yes, it works!

    This thing really works. If you are reading a review that says it doesn’t then they r either not using it correctly or using the wrong product. I did not get paid to use this product or my personal opinion like others. I didn’t want to spend all the extra money on a fancy brand name with the same results. My pics will speak for themselves. 

  5. Perfect nothing to say and accurate data super
    Thanks to seller send fast

  6. Lightly box is pressed in brightness, but writing data is no problem four yo ~

  7. Arrival a few days before the scheduled date, very satisfied. Well packaged, received intact and functional, perfect for sketches, simple design but good for the price. Comes with an anti-loss strap, and the pen easy to store.

  8. I arrived a week earlier than planned, I loved it coming with the battery included, very good product

  9. It didn’t take long to get there, all ok

DC 12V-36V 15A 500W Brushless Motor Controller Hall BLDC Driver Board Support Hall Motor

$18.19

Pricetug
Logo
Reset Password